Beadboard was 1 of the magic substances Alix Adams used to develop an adorable nursery for her soon-to-be-arriving baby girl Charlotte. Alix writes the DIY and craft site A Ruffled Lifestyle. She is such a devoted DIYer that she installed the beadboard in question when she was about seven months pregnant. But that just goes to present that this is certainly a extremely doable task for any person who’s keen to take it on.
Here’s Alix’s tutorial showing how to install beadboard wainscoting… and create an adorable infant’s room, also.
Incorporating woodwork into your house sometimes looks like an overpowering or hard job. The 1st time I stared at a pile of beadboard stacked in my garage I imagined to myself, what have I gotten myself into? But like a lot of home tasks, right after measuring twice and generating a couple of cautious cuts you turn into more comfortable channeling that inner carpenter. Putting in beadboard information all through your property is less difficult than you think! Come on, I will present you how to set up beadboard wainscoting, with a couple of ideas and tricks I realized along the way…
Resources and Supplies
Prior to we went to set up the beadboard there was some prep work that needed to be accomplished. The walls had been a beige brown, and that just wouldn’t do for my small chica. Soon after a number of journeys to The Residence Depot paint counter we settled on a wonderful peachy-pink color of paint (BEHR color: Friendship).
The very first item of prep operate was to paint the leading half of the walls peachy-pink (just the leading half due to the fact the bottom half we were going to cover in beadboard). We also painted the ceiling sound white. The two the ceiling and walls necessary three coats of paint to totally cover that beautiful brown-beige.
The second prep function item to tackle was framing the window in trim and putting in crown molding. These are completely optional, but they do include some added detail to the overall impact of the room.
Measure once, twice, thrice and then lower.
Let’s kick off this beadboard undertaking with a healthful dose of measuring.
To begin, measure the wall regions that you want to set up beadboard on. Then establish how a lot of pieces of beadboard you will need to cover that room. You will most most likely want to reduce some pieces of beadboard to match your area. This is exactly where the table saw comes in.
When the beadboard is reduce to fit, it is time to account for plug sockets and light switches. You will need to reduce out holes for all plug sockets and light switches that will be in the beadboard spot.
To do this, take away all plastic covers from plug sockets and light switches, measure where they are on the wall, and then transfer people measurements onto your beadboard. These measurements ought to be at least ¼ in. narrower than the plastic cover that goes above the plug sockets and light switches so that when the beadboard is set up the lights/plugs will sit on top of the beadboard edges (and wont sink into the wall then you push on them).
Time to reduce!
Now that you have the “cut” areas measured out on the beadboard designating exactly where plug sockets and light switches will go, I’m going to educate you some tricks on how to reduce holes in beadboard.
Initial, employing a ¼ in. drill bit, drill a hole in all four corners of the place the plug sockets and light switches will fit via. Following, insert a jig saw and reduce along your measured lines (from corner to corner). As soon as all holes are cut you are great to install the beadboard on your wall. Very carefully feed any plug sockets and light switches via the holes you reduce, producing positive that they rest flush with the beadboard.
Break out the nail gun, it’s party time.
To secure all the beadboard to the wall, we utilized a nail gun (super inexpensive instrument, BTW), generating confident to place nails the place studs had been situated. One nail at the best, middle, and bottom of the beadboard in spots where there have been studs ensured that the beadboard was going nowhere.
At this point you could also set up trim along the prime edge of the beadboard. Trimming out the spot where beadboard meets wall genuinely finishes off the seem. For the trim, measure all prime edges of beadboard, minimize it to size, and then nail in the trim in which studs are found.
Allow me just say, caulk and putty are like the magical fairy wand of carpentry…they make every thing all much better.
Critically however, I can’t emphasize adequate how much of a distinction some caulk work can make. Allow me educate you the caulk/putty techniques.
When you 1st install all the trim and beadboard you will observe some regions in which there are gaps or nail holes. Use caulk and a caulk gun to fill the gap areas. It is tough to sand caulk down, so make certain that the caulk is smooth ahead of it dries (utilizing your finger to smooth it out works like a charm).
To cover up any nail holes use putty (and a kitchen butter knife–I swear to you practically nothing performs greater) to fill in the hole. The putty need to be mounding up over the hole and you can go back once it dries and sand it down flush with your wood surface.
Paint all surfaces of your beadboard and trim.
Even though the trim and beadboard we purchased was previously primed in white paint, we noticed lots of marks left from installation, so we added two coats of white paint to all the beadboard and trim.
A valuable tip when painting is to use a excellent hand paintbrush to paint smaller sized places (e.g. all around a window) and edges that can’t be reached by a roller (e.g. corners and close to lights or plugs). It is also helpful to use painter’s tape to tape off any places that you do not want painted, like the place trim meets the wall.
Funnest step ever…remove all painter’s tape!
Make certain the paint is very good and dry prior to you rip off the tape.
Screw in all plastic light covers and plug covers.
You did it! I’m so proud of you. We need to get some lemonade to celebrate don’t you think?
I actually am so please with how this tiny girl’s room turned out. The beadboard and trim make all the difference. As a little reward for my challenging work I splurged on a chandelier for the area (also bought at the Residence Depot) and I feel it is the exclamation point at the finish of a profitable project!
Alix Adams has constantly been a maker-doer. She says that she would virtually get rid of her thoughts if she didn’t create things. On her site The Ruffled Daily life, Alix writes about crafts, entertaining, raising a family and existence in general. She lives with her husband and two children near Salt Lake City.
We have a lot far more DIY tasks here on The Home Depot website. Verify them out!
Pay a visit to our plank paneling and wood paneling sections on the web to see the a lot of beadboard and other wainscoting options accessible at The Residence Depot.
Feb 21, 2018 0Like Architecture & Interior Design? Follow Us… Need to revamp your living room, but not sure where to start? Pick grey to colour it. No longer associated with dungeons, dull office blocks...
1V0-601 test ?, 000-080 exam ?, ITILFND test ?, 70-488 dumps ?, PR000041 dumps ?, c2010-652 pdf , VCP550 Exam ?, 000-017 test ?, 300-115 certification ?, 300-208 Brain dumps ?, 70-246 dumps ?, 70-462 test ?, HP0-S42 test ?, 220-802 dumps , 300-135 pdf ?, OG0-093 pdf ?, SSCP certification , PMP dumps ?, SSCP dumps , LX0-104 exam ?, 300-208 exam , 1Z0-061 exam , 642-732 test ?, 70-411 Exam ?, 642-732 certification , EX200 pdf , 100-101 dumps ?, OG0-093 dumps ?, 642-999 test , MB2-707 certification ?, CAS-002 exam ?, 350-018 certification , NS0-157 exam , 000-105 pdf ?, NS0-157 dumps , 640-916 test ?, 1Z0-060 exam , 352-001 exam ?, 640-911 test , 70-346 pdf ?, 1Y0-201 exam ?, 642-999 pdf ?, ADM-201 pdf ?, 700-501 test ?, CAP exam ?, LX0-104 certification ?, CISM exam ?, 642-999 certification , 300-206 pdf ?, 70-463 certification ?, CAS-002 certification ?, 70-246 certification ?, 810-403 pdf , JK0-022 certification , CAS-002 test ?, 220-902 exam , 300-070 pdf ?, 70-534 test ?, c2010-657 dumps ?, 70-347 test ?, NSE4 test ?, 300-115 pdf , MB6-703 Exam ?, CCA-500 test ?, 70-483 dumps ?, ITILFND certification ?, 300-101 exam , PEGACPBA71V1 dumps ?, 1Z0-051 exam ?, 70-347 certification ?, 300-320 Brain dumps ?, 000-106 certification ?, 300-208 test ?, 220-802 certification ?, 1Z0-060 exam ?, 74-678 certification ?, 1Z0-061 dumps ?, 1Z0-144 Study Guides ?, 70-346 exam ?, 210-260 certification ?, 640-692 test ?, 642-732 test ?, ICGB certification , 74-678 dumps ?, 350-018 exam , 1Z0-061 Study Guides ?, 000-080 certification ?, CISM dumps , 1Z0-803 exam ?, LX0-103 Brain dumps ?, CRISC certification ?, 220-901 exam , 1Z0-804 dumps ?, 9L0-012 dumps ?, 300-320 dumps ?, MB5-705 exam ?, SSCP certification ?, MB2-704 dumps ?, 70-486 dumps ?, 1z0-434 Study Guides ?,